GRAB BAR MOUNTING KITS Snap Toggle bolts Stainless Steel 6 Pack.Install a Grab Bar.Any bathroom can benefit from the added safety of grab bars.They are very effective in helping prevent slips and falls in the bath.Read on to learn tips on how to install grab bars in your bath.Where to Install Grab Bars.Try climbing in and out of your tub or showerminus the waterto get an idea where grab bars should be placed, and mount them where they work best for everyone using that bathroom.Always mount grab bars into a stud that sits behind the wall.Or, if the stud cant be located, use an anchoring device.Be sure there is adequate room within the hollow area behind the wall so an anchoring device will work.Grab bars can be placed vertically, horizontally or diagonally depending on your needs.At the entry to the shower or tub.To help facilitate entry and exit, install a grab bar vertically in front of the shower or tub.A smaller grab bar 1.Having a grab bar here helps prevent the tendency to reach for towel bars, sliding glass doors or other unstable fixtures.Vertical grab bars are also good for both shorter and taller people to grip at a comfortable height.In the shower or tub.Horizontal grab bars mounted inside the tub or shower provide added stability, whereas diagonal grab bars provide added stability when lowering to sit on a shower seat.Generally a 1. 6 in grab bar or a grab bar that is a multiple of 1.In most cases studs are located 1. How To Print Double Sided In Adobe Acrobat Reader Dc . Always attach grab bars to studs or use secure mounting anchors the manufacturer recommends.Near the toilet. Installing a grab bar near the toilet can provide great assistance in both sitting or standing.Used in conjunction with a chair height toilet or raised toilet seat and this can further improve comfort and ease of use.Generally, a grab bar is installed either horizontally or diagonally near the toilet.A diagonal grab bar is more in tune with the natural movement of the hand and wrist and puts less strain on the wrist.They also offer the ability to grip at varied heights, making them comfortable for both shorter and taller people.When installed diagonally, a grab bar may not reach between studs.How To Install A Grab Bar In The Bathroom' title='How To Install A Grab Bar In The Bathroom' />If this is the case, it can be mounted with secure mounting anchors used at one or both ends of the grab bar.Install Grab Bars in Your Bathtub Over Studs.Step 1. Mark mounting locations on the wall with strips of 1 12 in painters tape at the height you need and roughly as long as the grab bar you want.How To Install A Grab Bar In The Bathroom' title='How To Install A Grab Bar In The Bathroom' />Most building codes require a grab bar to support at least 2.To get that kind of sturdiness, screw the mounting brackets into the wood studs holding up the wall.Step 2. Using a stud finder, locate the positions of wall studs and mark them on the painters tape strips.Double check your marks to pinpoint the stud centers.Step 3. Using the grab bar mounting flange as your guide, mark the pilot hole locations oriented over your stud marks.For mounting on drywall, youll need to drill pilot holes using a bit thats slightly smaller than the shaft of the mounting screw the core that the threads wrap around.Check the directions for a manufacturers recommendation.Drill pilot holes through the drywall and check to make certain you drilled into a stud on the other side.If youre drilling through ceramic tiles, you need glass tile drill bits.For driving screws into a stud, use a 14 in bit to drill only through the tile and part of the drywall but not into the stud.For installing the Snaptoggle anchors used here, drill a 12 in hole through both the tile and drywall.Using a glasstile bit requires two extra precautions.First, slow the drill speed down to about 3.Higher speeds only add bit dulling heat.Second, have a helper with a spray bottle of water mist the tip of the bit regularly as you drill to help keep it cool.Step 4. Drive the mounting screws that came with your grab bar, or use 2 12 in panhead screws.Pay attention to the resistance you feel as you drive the screws.If you feel the resistance slack off before youre finished, that could be a sign the screw tip broke through the side of the stud, reducing its strength.Long screws can tax your drill or drivers strength.To avoid stripping out the screw head, apply candle wax beeswax works well along the threads before driving each screw.Youll reduce the friction without reducing their grip.Step 5. Slide the grab bar covers over the mounting flanges and apply moderate pressure to the bar to test the strength.Mount a Grab Bar With Wall Anchors.The grab bar directions call for three screws per flange, which works fine for mounting on studs.But drilling that many 12 in holes in plain drywall can weaken the wall enough for the mounting area to break off.Instead, use two heavy duty toggle bolt anchors placed in the upper half of the flange with the metal channels positioned vertically.You can use three anchors per flange in tile over drywall and in plaster wallsparticularly plaster over lathbecause both are stronger than plain drywall.Step 1. Mark the flange hole openings on painters tape and find the center of each hole as you would for driving screws into a stud.Tape also helps keep the bit from wandering and tile from cracking as you start the hole.For the Snaptoggle anchors used here, we drilled 12 in holes and carefully removed any loose pieces of drywall paper.Step 2. Hold the metal channel against the anchors plastic straps, slide it through the hole, and make certain the metal channel is vertical.Hold the ends of the plastic straps and pull them toward you until the channel seats against the back side of the wall.Slide the plastic cap along the mounting with your other hand until the cap is flush against the wall.If the cap isnt tight against the wall, the slack between the cap and the metal channel can allow the anchor to spin around as you tighten the mounting screw.For a tight connection, press against the cap with the edge of a screwdriver while you tug on the plastic straps to remove any slack.Step 3. Using the screws supplied with the anchor, fasten the mounting flanges to the wall on both ends.Apply equal pressure to the screws holding each flange to prevent the bar from rocking and damaging the drywall.Tighten the screws until theyre finger tight against the mounting flange, then add a half turn.Step 4. Slide the covers over the flanges and give the bar a strong pull to test the strength of the bar.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |